...

Boat and trailer cleaning guidelines to prevent the spread of... Boat and Gear Disinfection Protocol

by user

on
2

views

Report

Comments

Transcript

Boat and trailer cleaning guidelines to prevent the spread of... Boat and Gear Disinfection Protocol
Boat and Gear Disinfection Protocol
Boat and trailer cleaning guidelines to prevent the spread of aquatic invasive species have been widely distributed to the
public through a variety of publications, pamphlets, signs, etc. The guidelines consist of a nationally-accepted set of
prevention steps. While disinfection is not a required prevention step for the general public, some boaters may be interested
in the disinfection procedures followed by the WI DNR. Please note: the first three steps (Inspect and Remove, Drain, and
Dispose) listed below are required.
The following steps shall be taken every time a boat, equipment or gear is moved between waters to avoid
transporting invasive species and/or pathogens:
♦ Inspect and remove aquatic plants, animals, and mud from your boat, trailer, equipment and gear.
♦ Drain all water from your boat, motor, live well, bilge, transom wells, as well as from your equipment and gear,
including but not limited to tracked vehicles, barges, silt or turbidity curtain, hoses, sheet pile and pumps.
♦ Dispose of unwanted aquatic plants and animals in an appropriate way.
♦ Disinfect your boat, equipment and gear by either:
♦ Washing with ~212º F water (steam clean), OR
♦ Drying thoroughly for 5 days after cleaning with soap and water and/or high pressure water, OR
♦ Disinfecting with either 200 ppm (0.5 oz per gallon or 1 Tablespoon per gallon) Chlorine for 10-minute contact time
or 1:100 solution (38 grams per gallon) of Virkon Aquatic for 20- to 30-minute contact time. Note: Virkon is not
registered to kill zebra mussel veligers nor invertebrates like spiny water flea. Therefore this disinfect should be
used in conjunction with a hot water (>104º F) application.
Safety Precautions for Disinfectant Use:
Virkon-A:
1. Receive and be required to read a copy of the Virkon-A Materials Safety Data Sheet (MSDS) for the product.
2. Wear chemical splash goggles.
3. Wear a face shield where the possibility exists for face contact due to splashing or spraying of the material.
4. Wear impervious clothing to prevent contact with skin. (gloves, pants, jacket, hood, and boots) or a Tyvek style
full body suit.
In addition, all employees who handle or mix Virkon-A in powder form and prefer to wear a dust mask respirator
when handling powder, may do so in compliance with the DNR Respiratory Protection Program Handbook MC
9180.5 Voluntary Use requirements.
Bleach:
Follow precautions 2, 3, and 4 (above).
Chlorine Wear eye protection, rain gear, gloves if spraying. Stay upwind of the spray. Will break down in
sunlight and when in contact with organic material. Is corrosive to metal and rubber. Is toxic to fish at
these concentrations so rinse well after disinfection or neutralize with sodium thiosulfate. For neutralizing
chlorine, spray sodium thiosulfate in an 800 ppm solution (3 grams per gallon of water) on all surfaces after
the disinfection period is over. Rinse with water from the next lake to remove any remaining sodium
thiosulfate.
o Virkon Aquatic This is a disinfectant in the peroxygen (hydrogen peroxide) family. It is a powder. It is
99.9% biodegradable and breaks down to water and oxygen and is not corrosive at the working dilution.
Wear dust mask if mixing powder and eye protection, rain gear and gloves if spraying. Stay upwind of
spray.
Sources of disinfectants
Chlorine - Household bleach (5.25% chlorine) can be purchased from a grocery or convenience store. HTH is granular
chlorine (70% calcium hypochlorite) and can be purchased from a pool supply company.
Sodium Thiosulfate - Commonly used to neutralize chlorine and iodine. It should be available at a pool supply
company or from a chemical supply company.
Virkon Aquatic is available from Western Chemical. It is the same formulation, but without the perfume and dye, and
the label addresses specific fish pathogens. Their phone is 1-800-283-5292.
o
Disinfection measures must be taken prior to moving boats, equipment and other gear from one waterbody to another. They
are not needed daily when sampling the same waterbody or for law enforcement equipment in emergency situations. In cases
where boats and gear return to state hatcheries, disinfection should be done in a location away from ponds and water supplies
to prevent disinfectant or untreated water from entering those areas. Every effort should be made to keep the disinfection
solution and rinse water out of surface waters.
To the extent practicable, equipment and gear used on waters known to be infested with invasive species and viruses should
not be used on other non-infested waters. The following are some helpful hints to consider when planning your work in
water.
¾
¾
¾
Organize your sampling so the work in infested waters is always done last.
If a high percentage of your work is done in waters with invasive species, consider dedicating certain gear to be used
only in those waters.
Depending on the type of work you are doing, it may be possible to work with lake volunteers and use their boats to
collect samples. That way only your gear needs to be disinfected.
The following methods are provided to assist staff when disinfecting equipment and gear commonly used by
department staff.
Nets
Organic debris should be removed prior to disinfection. Power washing is not required, but nets could be sprayed with a
garden hose to remove debris. Nets may be steam cleaned, washed and dried thoroughly for five days or treated with a
disinfection solution. Nets should be placed in the disinfection solution for the appropriate contact time for the solution being
used. After rinsing, the nets can be used immediately, or hung to dry.
Personal protective gear, including rain gear, gloves, boots/waders
Scrub personal protective gear with the disinfection solution. After scrubbing, the gear should be kept wet with the
disinfection solution for the appropriate contact time. Rinse with clean water or water from the next waterbody.
Alternatively, personal gear may be steam cleaned or dried thoroughly for five days after cleaning with soap and water.
Dip nets, measuring boards and other sampling gear
Remove any organic material from sampling gear. There are several options for disinfecting smaller gear. Dissolved oxygen
probes and other sensitive electronic sampling gear may be damaged by disinfection solution and should only be rinsed with
clean water. For other gear used in water choose one of the following options:
¾
¾
¾
Option one: The gear can be sprayed with the disinfection solution and a wet surface maintained for the appropriate
contact time. The gear should be rinsed with clean water or water from the next waterbody before it is used again.
Option two: Fill a tub with disinfection solution and place all equipment in the tub for the appropriate contact time.
The gear should be rinsed with clean water or water from the next waterbody before it is used again.
Option three: Use a completely new set of gear for each waterbody during the work day and disinfect all gear at the
end of the day using option one or two.
Boats, trailers, and live wells
Remove organic material from boats, trailers, and live wells. Drain water from live wells, bilges and pumps. The outside
and inside of the boat, trailer, live wells, bilges, and pumps should be sprayed with the disinfection solution and left wet for
the appropriate contact time. The inside of the live wells, bilges and pumps should be made to contact the solution for the
appropriate contact time as well. Run pumps so they take in the disinfection solution and make sure that the solution comes
in contact with all parts of the pump and hose. The boat, trailer, bilges, live well, and pumps should be rinsed with clean
water or water from the next waterbody after the appropriate contact time. Every effort should be make to keep the
disinfection solution and rinse water out of surface waters. Pull the boat and trailer off the ramp and onto a fairly level area
and away from street drains to minimize potential runoff into surface waters.
Motors
After removing from the water, tip the motor to the down position and start the motor for several seconds or turn motor over
several times to dispel water from the cooling system. Alternatively and especially for motors moored in water for several
days or more, emerge the lower unit in a bucket of disinfectant and run the motor to ensure contact with all internal parts and
allow for the appropriate contact time. Or, rig up a short (6-foot) piece of garden hose to lower unit muffs. A pail of the
disinfectant can be set in the back of the boat and gravity fed to the lower unit to run the disinfectant through the motor.
Allow solution to remain in motor for the appropriate contact time. The hose will need to be primed to start the gravity flow
because the lower unit does not create enough suction to prime the hose. A non-corrosive (Virkon Aquatic) is recommended
for use to protect the impeller. Rinse with clean water or water from the next waterbody.
Heavy Equipment
For heavy equipment steam-cleaning is an effective method of disinfection.
Fly UP